Vial labels that survive the fridge: what to write, what to use, and a free printable sheet

VialHaus 30 Vial Case open, with a row of capped vials in its sockets

A vial label has a hard life. It sits on a curved surface about the width of a pencil, it goes in and out of a cold, damp box, and it rubs against other vials and fingers. Most labels that fail in a fridge fail for one of three reasons, and all three are cheap to fix.

If you only want the sheet: our free printable vial label sheet (PDF) has 76 small labels and 30 larger ones, numbered to match the sockets in a case. The rest of this page is how to make any label last.

Why vial labels fail in the fridge

  • Condensation. A cold vial taken into a warm room is wet within seconds. Paper soaks it up, water-based ink runs, and the adhesive lets go at the edges.
  • The curve. A 3 ml vial is about 16 mm across. A stiff label on that curve wants to spring flat, so the corners lift first, then the edges catch on everything.
  • Rubbing. Loose vials in a tray or a door shelf knock and slide against each other. A month of that wears a written date down to a smudge.

What to write on a vial label

Four things, and nothing you will not read again:

  1. What it is. The name on the original box or label, written the same way every time.
  2. The date it went in (or the day you mixed it).
  3. The date it comes out. Work it out once, when you write the label, not later from memory. The vial expiry calculator and date tracker does the maths in your browser.
  4. A number that matches the socket it lives in. That one line is what lets you find the right vial without reading every label.

Keep the label smaller than the way round the vial, so a strip of glass stays clear. You want to see what is inside without peeling anything off.

Sizes: 3 ml and 10 ml vials

A 3 ml vial is about 16 mm across, so the way round is about 50 mm, with roughly 30 mm of usable height between the shoulder and the base. A 10 ml vial is about 22 to 24 mm across, so about 70 to 75 mm round, and taller. A label about 45 mm wide fits a 3 ml vial with a clear strip left over; on a 10 ml vial the same label leaves a wide window. More on the two sizes in 3 ml vs 10 ml vials.

Which label, which pen

  • Plain paper and clear tape. The cheapest way that works. Write first, then wrap clear tape all the way round the vial over the paper so the tape sticks to itself. Water cannot get under it.
  • Waterproof label stock (polyester or vinyl). Holds up to condensation without tape. Sold in A4 and US Letter sheets for home printers; look for the word waterproof, not just water resistant.
  • Freezer labels. Made for cold, damp surfaces. They are the safest choice if a vial ever goes in the freezer or a cooler with ice packs.
  • A label maker with plastic tape. Neat, waterproof and quick. Use narrow tape and leave the window clear.
  • Pens: a fine permanent marker or a ballpoint. Avoid gel pens and anything that smudges on a wet finger.

How to put a label on so it stays

  1. Write the label first, on the table. Writing on a vial is harder and messier.
  2. Label a dry vial at room temperature. If the vial is already cold, take it out, let it reach room air, and dry it before the label goes on.
  3. Press from the middle out, then hold it for a few seconds so the adhesive takes the curve.
  4. Seal the edges with a wrap of clear tape if the label is paper.
  5. Put it back in its numbered socket, oldest on the left.

The numbered system

A number on each label and the same number on each socket turns a fridge shelf into a list. Write the number on the label, keep the vial in that socket, and log the same number in the Date Tracker. When you open the case, the oldest vial is always the one on the left, and you never have to turn a vial round to read it.

Our 30 Vial Case has numbered rows that map to the tracker; the 15 Vial Case works the same way with fewer sockets. If you are choosing a case, the vial case buying guide has the checklist, and how to organize vials in the fridge has the rest of the routine.

The free VialHaus label sheet

  • Page 1: 76 small labels with a number, an in date, an out date and a contents line, sized for 3 ml vials.
  • Page 2: 30 larger labels with an extra notes line, for 10 ml vials, boxes or the case itself.
  • Printed on A4. On US Letter, choose fit to page in the print dialog.
  • Plain paper with clear tape works; A4 or Letter label stock is neater.

Download the label sheet (PDF). It is free, no email needed, and it also comes with every VialHaus order together with the Date Tracker and our travel card.

Common questions

What size label fits a 3 ml vial? About 45 mm wide and no more than about 30 mm tall, so it wraps most of the way round and leaves a clear strip.

Will a paper label survive the freezer? Not on its own. Use freezer labels or waterproof stock, or seal paper under clear tape all the way round.

Can I write directly on the glass? A fine permanent marker writes on glass, but it rubs off where fingers hold the vial. A label lasts longer.

Do I need to label vials in a case? Yes. The case keeps vials upright and apart; the label tells you which one is which and when it comes out.

Storage accessories only. Follow the storage instructions on your own label.